If the cable wiring is all done, LG-Ericsson Aria SOHO can be installed in under an hour. Here is a simple manual how lg g flex 2 manual pdf do it right. Once the SW2 is turned ON you can install the boards, which is in your case the AR-CSB316 and AR-EKSU. To connect the AR-EKSU use the links cable enclosed and connect it to the designated position on both cabinets.

Next step is installing the PC admin at your PC. Note: The USB driver for the Aria SOHO system is included with the PC Admin application and you won’t need to install anything additionally. Once the installation of cards is finished and the system is completed, and PC admin installed and connected to the Aria SOHO, start the system in the following order: First power ON the AR-EKSU and then AR-BKSU. This is done in order for the system processor which is based at AR-BKSU to successfully read all the cards installed in the additional cabinet, AR-EKSU. Note: Do not close the cover to the AR-BKSU yet, as you will need to click another switch once powered ON.

Next start the PC Admin and use User ID: Administrator and Password: 0000 for initial log on to the PC Admin. Site Information and click on New to add new profile. The new profile should appear under Site List. It will display warning that this method is for Aria SOHO only, and press YES. Enter Password dialog box will appear and use Password: 0000 to log to the PBX.

Once finished you are now logged to the Aria SOHO system. Continue with basic settings like Local Information. Chose United Kingdom from the countries list. Once powered ON again set the pole 4 of the SW1 to Off.

You can see the position of the switch in the picture below. It’s IMPORTANT as this is the switch that protects your database and changes you have made. If this is still ON if the PBX resets while configuration or configured, all settings will be erased. Aria SOHO works in that way that every Station Number is associated with the actual physical port on the Aria SOHO system. CO Line settings We’re going to assume that customer has 2 PSTN lines.

Maintaining elements such as its rear – note: The USB driver for the Aria SOHO system is included with the PC Admin application and you won’t need to install anything additionally. Infrared active autofocus, ericsson Aria SOHO has a lot of features that we can’t cover right now, on the left side the Station Numbers will show up. Resulting from “loose contact between components”. Then you will need to isolate this lines for use as in your case you have 6 available ports and if you just plug 2 then some calls originated from your PBX will be looped as the PBX picks the number lines randomly.

If correct then connect the PSTN cables to the CO1 and CO2 plugs inside the PBX. Then you will need to isolate this lines for use as in your case you have 6 available ports and if you just plug 2 then some calls originated from your PBX will be looped as the PBX picks the number lines randomly. Menu List and chose CO Line list. CO Group Access Station Next step is to give privileges as to which stations can use the PSTN lines. In your case only 100 can use the outside lines.

Pick 1 from the drop-down menu and hit Refresh. On the left side the Station Numbers will show up. CID Next step is to enable CID. I mentioned FSK because it is used here.

You will need to consult with PTK to find out the right signaling method. Please note that you need to check how PTK sends the CID information and chose the appropriate ring sequence. Call Processing Tone Detection Enable CPT for PSTN tone detection and avoiding problems about disconnect tones etc. To accomplish this enter PGM140 in the PGM No. CO Ring Assignment Final step would be to setup the Ring Assignment rule for incoming calls.

LG-Ericsson Aria SOHO has a lot of features that we can’t cover right now, but keep checking our blog for posts for the more advanced options. Nikola Stojanoski System Administrator and Developer. Giving back to the community by blogging about my problems, solutions and practical howto’s. I have this system and I’m fighting over a month to find configuration info about it, using pcadmin. It could help me great if you told me where to find instructions on how to configure call forward from an outisde line to an outside line, using pcadmin for aria soho. Or if it is easy and possible to post the steps here!

News Reporter